Help with TiLP

Shadow Phoenix · Post by **Shadow Phoenix** » Sun 10 Apr, 2005 8:15 pm

I have Windows. I have Tilp. I also have Ti-84+se . I have a black cable connecting USb -> Usb
I have installed the drivers So it says: TI-GRAPH/DIRECT LINK USB.
When I try to do anything it thinks for a second " calculator stops responding" and then it says :
"
Msg: Invalid host ID.
Cause: TiLP received an unexpected Machine ID, probably due to a transmission error.
"

Andy_J · Post by **Andy_J** » Sun 10 Apr, 2005 8:34 pm

I don't think TiLP supports the 84+ direct USB on Windows yet.

Shadow Phoenix · Post by **Shadow Phoenix** » Sun 10 Apr, 2005 8:38 pm

so it supports silverlink only?

Andy_J · Post by **Andy_J** » Sun 10 Apr, 2005 10:04 pm

I could be wrong, though. I don't really have a reason to find out.

Shadow Phoenix · Post by **Shadow Phoenix** » Sun 10 Apr, 2005 10:20 pm

it does not support Direct usb cables....*cries*
*looks at someone* o you have an image I can use of Ti84+se?

Andy_J · Post by **Andy_J** » Mon 11 Apr, 2005 1:42 am

What would you use it with anyway?

Shadow Phoenix · Post by **Shadow Phoenix** » Mon 11 Apr, 2005 1:50 am

Tilem....so I would get normal screenshots/ sppeds. Since VTI/Flash Debbuger display grayscale badly...

Post by **benryves** » Mon 11 Apr, 2005 9:34 am

I just wish people still used the blacklink cables... I get all sorts of "when are you porting xxx to USB?" queries. Serial is nice and easy to code for.

(Also known as: I have no idea how to control USB).

Andy_J · Post by **Andy_J** » Mon 11 Apr, 2005 1:45 pm

Doesn't work that way when new computers don't have RS-232 ports. -_-

Post by **Patori** » Mon 11 Apr, 2005 1:47 pm

benryves wrote:I just wish people still used the blacklink cables... I get all sorts of "when are you porting xxx to USB?" queries. Serial is nice and easy to code for.
(Also known as: I have no idea how to control USB).

heheh, rock on! me too!

Shadow Phoenix · Post by **Shadow Phoenix** » Mon 11 Apr, 2005 8:55 pm

ok I got a Grayscale cable. Tried to send /recieve files. It works smoothly/perfect. However when I attempt a Rom dump it gives me this error :
"Msg: Checksum error.
Cause: a transmission error. Try again."
And so I have to reset my calc by pulling the batteryies. Once I got 10K out of 512, but that was my max.

Shadow Phoenix · Post by **Shadow Phoenix** » Mon 11 Apr, 2005 11:26 pm

Ok I tried it on Ti-83+ non silver and it still gives me the same error. It transfers the Rom Dumping program all right, but when I do ASM(Rom83P it crashes and just displays 0 K out of 512K .
So does anyone has an ASM program sending Rom to ANY ports?

DJ_O · Post by **DJ_O** » Mon 11 Apr, 2005 11:31 pm

DUmping the ROM should normally take around 30 minutes with VTI, just wait one minutes at least to see if it will increase at 1%

Shadow Phoenix · Post by **Shadow Phoenix** » Mon 11 Apr, 2005 11:37 pm

it gives me an error around a few seconds after the program starts...

DJ_O · Post by **DJ_O** » Mon 11 Apr, 2005 11:40 pm

Which ROM do u have? Try to not dump anything higher than version 1.12, as VTI only support 1.12. If you are going to use this rom with Alpha make sure you have 1.14 or lower