One of my good friends (Curious Onlooker on OTBP) messed up his calculator (I have it in my possession now, so that I can attempt to fix it).
When you turn the calculator on, immediately a RAM clear message is displayed, and the calculator turns off. However, you hold down the on button, the calculator does not turn off.
He says that he has tried everything (taking out back up battery, ON+Del with or without the batteries in, etc), and now referred to me.
Please give me some advise / help!
Thanks!
Help With Friend's Calculator that is screwed
Moderator: MaxCoderz Staff
- JoostinOnline
- Regular Member
- Posts: 133
- Joined: Wed 11 Jul, 2007 10:42 pm
- Location: Behind You
Re: Help With Friend's Calculator that is screwed
What do you mean, without the batteries? Instead of ON+Delete, just hold down delete, remove a battery, then re-insert it (all while holding Delete). This should bring up "Waiting for TI-OS" or somthing like that. Now send an OS from your computer or another calculator.b-flat wrote: ON+Del with or without the batteries in
Re: Help With Friend's Calculator that is screwed
OK, thanks.JoostinOnline wrote:What do you mean, without the batteries? Instead of ON+Delete, just hold down delete, remove a battery, then re-insert it (all while holding Delete). This should bring up "Waiting for TI-OS" or somthing like that. Now send an OS from your computer or another calculator.b-flat wrote: ON+Del with or without the batteries in
I thought that he had tried that, but he evidently didn't. I'm just going by what he told me.
I don't know if the problem will be solved by resending the OS, but at least the screen comes up.
- calc84maniac
- Regular Member
- Posts: 112
- Joined: Wed 18 Oct, 2006 7:34 pm
- Location: The ex-planet Pluto
- Contact:
What do I have to do with anything? Other than something like this happened to my first calc and I didn't know about the Del trick...kalan_vod wrote:It should, you might want to email the maker of the oncalc assembler. Make sure include if he had any hooks installed (noshell xlib omnicalc etc..).
~calc84maniac has spoken.
Projects:
F-Zero 83+
Project M (Super Mario for 83+)
Projects:
F-Zero 83+
Project M (Super Mario for 83+)
It may not be your fault, just wanted to send him in a direction or two.calc84maniac wrote:What do I have to do with anything? Other than something like this happened to my first calc and I didn't know about the Del trick...kalan_vod wrote:It should, you might want to email the maker of the oncalc assembler. Make sure include if he had any hooks installed (noshell xlib omnicalc etc..).
Well, actually, OTBP assembler WAS related in the event, though everything is fine now.
The best that I can remember:
* was assembling a very simple program to simply display "RAM Cleared" (nothing special; homescreen only)
* there was an error at the very end of assembling (i.e. when one of the ASM routines was copying the code to a program), so he used GrpTool to try and get a new version of OTBP assembler, from the group.
* everything was messed up while using group tool (garbage, etc, was displayed)
I can't quite remember exactly when, but at some point, he used Omnicalc's RAM recovery feature and then, after all of this, at some point, the error occurred.
I'll post it in a more detailed fashion once I get more specific info.
The best that I can remember:
* was assembling a very simple program to simply display "RAM Cleared" (nothing special; homescreen only)
* there was an error at the very end of assembling (i.e. when one of the ASM routines was copying the code to a program), so he used GrpTool to try and get a new version of OTBP assembler, from the group.
* everything was messed up while using group tool (garbage, etc, was displayed)
I can't quite remember exactly when, but at some point, he used Omnicalc's RAM recovery feature and then, after all of this, at some point, the error occurred.
I'll post it in a more detailed fashion once I get more specific info.